Lim Yee Wei Posted May 11, 2020 Posted May 11, 2020 I used a Y splitter n connect to both sub from one sub out n both works Sent from my iPhone using Tapatalk
petetherock Posted May 11, 2020 Posted May 11, 2020 I used a Y splitter n connect to both sub from one sub out n both works Sent from my iPhone using Tapatalk That shows the subs work. Then it could be a non functional sub out 2 port.. Since this model can't calibrate two subs independently, you might as well use the y-splitter.. just set them at close to the same distance or get a Mini-DSP..
Lim Yee Wei Posted May 11, 2020 Posted May 11, 2020 That shows the subs work. Then it could be a non functional sub out 2 port.. Since this model can't calibrate two subs independently, you might as well use the y-splitter.. just set them at close to the same distance or get a Mini-DSP.. I tried both sub out individually both works So really no idea what’s wrong Sent from my iPhone using Tapatalk
Guest wcseow Posted May 11, 2020 Posted May 11, 2020 Just a thought, did u try having the power selector to be on, in case u have set it to auto? I have a number of SW12s, I find it is safer to have it to be on as sometimes it does not kicked in. Hope it help
petetherock Posted May 11, 2020 Posted May 11, 2020 I tried both sub out individually both works So really no idea what’s wrong Sent from my iPhone using Tapatalk Initial configuration setup page- you specified two subs ya?
rayleh Posted May 12, 2020 Posted May 12, 2020 Initial configuration setup page- you specified two subs ya? Yes, Pete may be right. Did configure as 2 subs? Sent from my iPhone using Tapatalk
dbchoong Posted May 12, 2020 Posted May 12, 2020 For the X1200, I think there is no specification of 1 or 2 subs. I think it only has Subwoofer : YES/NO. The output on both sub outs are the same.
desray Posted May 12, 2020 Posted May 12, 2020 For the X1200, I think there is no specification of 1 or 2 subs. I think it only has Subwoofer : YES/NO. The output on both sub outs are the same. That’s interesting to know... Sent from my iPad using Tapatalk
desray Posted May 12, 2020 Posted May 12, 2020 Just a thought, did u try having the power selector to be on, in case u have set it to auto? I have a number of SW12s, I find it is safer to have it to be on as sometimes it does not kicked in. Hope it help Yes, this is possible if not the LFE signal (gain) not strong enough...but I doubt this will be the case. BTW Danlim, what subwoofers are you using? Sent from my iPad using Tapatalk
pcking1624705747 Posted May 12, 2020 Posted May 12, 2020 He is using the Starke SUB24 BTW Danlim, what subwoofers are you using? Sent from my iPad using Tapatalk
desray Posted May 12, 2020 Posted May 12, 2020 He is using the Starke SUB24 Thanks...from the rear view, connection look simple and straightforward. So I've no doubt that danlim have any connection problem.
Gondon72 Posted May 12, 2020 Posted May 12, 2020 From German forum people are saying there will be announcement this week. Then i found this website news. http://world-today-news.com/denon-answers-questions-about-av-receivers-multiroom-audio-and-hdmi-2-1-in-the-livestream/ :D
econav Posted May 12, 2020 Posted May 12, 2020 But only one sub is working when I calibrated using audyssey Sent from my iPhone using Tapatalk For Starke SUB24 , if you are connecting only a RCA to the sub .Please connect to the Red RCA connector.
dbchoong Posted May 15, 2020 Posted May 15, 2020 How to enable Speaker Virtualizer in the Denon X3600?
rayleh Posted May 15, 2020 Posted May 15, 2020 According to the manual, you can set it at the Surround Parameter under the Audio Option on the menu. BTW it stated this option is only available under firmware update so I am not sure if it is available yet.
desray Posted May 15, 2020 Posted May 15, 2020 According to the manual, you can set it at the Surround Parameter under the Audio Option on the menu. BTW it stated this option is only available under firmware update so I am not sure if it is available yet. I believe it is for 2.1 setup only? Sent from my iPhone using Tapatalk
FookLai Posted May 18, 2020 Posted May 18, 2020 My trustworthy 7200 recently has HDMI issue, any forum member here has experiences the same? If yes, how do you resolve it? 1) I first found out that the main zone main HDMI output (monitor 1) was not working and at the same time receiver couldnt receive any HDMI signal as well. 2) After that, strangely, when I unplugged the HDMI output from monitor 1, the HDMI input signal either from Panasonic 820 or Zidoo Z9S work. 3) Then I tried to plug the HDMI to 7200 monitor 2 output and it works. 4) A few days later, the monitor 2 output started to exhibit the same issue as monitor 1 output. It doesn't have any output signal and whenever the output is connected, the HDMI input receive no signal. 5) Now, I have used the final trick which is to connect the output to zone 2 HDMI output. Fortunately it is a pass through, so I get back the picture through zone 2 while sound through main zone, both zone set to same input. Any help would be much appreciated.
desray Posted May 18, 2020 Posted May 18, 2020 My trustworthy 7200 recently has HDMI issue, any forum member here has experiences the same? If yes, how do you resolve it? 1) I first found out that the main zone main HDMI output (monitor 1) was not working and at the same time receiver couldnt receive any HDMI signal as well. 2) After that, strangely, when I unplugged the HDMI output from monitor 1, the HDMI input signal either from Panasonic 820 or Zidoo Z9S work. 3) Then I tried to plug the HDMI to 7200 monitor 2 output and it works. 4) A few days later, the monitor 2 output started to exhibit the same issue as monitor 1 output. It doesn't have any output signal and whenever the output is connected, the HDMI input receive no signal. 5) Now, I have used the final trick which is to connect the output to zone 2 HDMI output. Fortunately it is a pass through, so I get back the picture through zone 2 while sound through main zone, both zone set to same input. Any help would be much appreciated. Change a HDMI cable or better still, upgrade to a new AVR. :)
petetherock Posted May 18, 2020 Posted May 18, 2020 My trustworthy 7200 recently has HDMI issue, any forum member here has experiences the same? If yes, how do you resolve it? 1) I first found out that the main zone main HDMI output (monitor 1) was not working and at the same time receiver couldnt receive any HDMI signal as well. 2) After that, strangely, when I unplugged the HDMI output from monitor 1, the HDMI input signal either from Panasonic 820 or Zidoo Z9S work. 3) Then I tried to plug the HDMI to 7200 monitor 2 output and it works. 4) A few days later, the monitor 2 output started to exhibit the same issue as monitor 1 output. It doesn't have any output signal and whenever the output is connected, the HDMI input receive no signal. 5) Now, I have used the final trick which is to connect the output to zone 2 HDMI output. Fortunately it is a pass through, so I get back the picture through zone 2 while sound through main zone, both zone set to same input. Any help would be much appreciated. I hope you are not hot unplugging the cables bro.. but the HDMI board is probably about 4-5 years old and seems to be telling you it's giving up the ghost. Try using a cooling fan, and check the cost of spares.. or like bro Des said, time for a new amp ;)
desray Posted May 18, 2020 Posted May 18, 2020 I hope you are not hot unplugging the cables bro.. but the HDMI board is probably about 4-5 years old and seems to be telling you it's giving up the ghost. Try using a cooling fan, and check the cost of spares.. or like bro Des said, time for a new amp ;) Oh yes, please don't ever do that out of convenience. You will short the HDMI board.
Audio Posted May 18, 2020 Posted May 18, 2020 My trustworthy 7200 recently has HDMI issue, any forum member here has experiences the same? If yes, how do you resolve it? 1) I first found out that the main zone main HDMI output (monitor 1) was not working and at the same time receiver couldnt receive any HDMI signal as well. 2) After that, strangely, when I unplugged the HDMI output from monitor 1, the HDMI input signal either from Panasonic 820 or Zidoo Z9S work. 3) Then I tried to plug the HDMI to 7200 monitor 2 output and it works. 4) A few days later, the monitor 2 output started to exhibit the same issue as monitor 1 output. It doesn't have any output signal and whenever the output is connected, the HDMI input receive no signal. 5) Now, I have used the final trick which is to connect the output to zone 2 HDMI output. Fortunately it is a pass through, so I get back the picture through zone 2 while sound through main zone, both zone set to same input. Any help would be much appreciated. This is due to a HDMI cable in your setup is having the common "handshaking problem". Just one intermittent HDMI cable will screw up everything. Just isolate the one cable that is giving this problem if it is still in the system and replace this. My personal cure from this was to change everything to optical HDMI. (Audio)
FookLai Posted May 18, 2020 Posted May 18, 2020 I hope you are not hot unplugging the cables bro.. but the HDMI board is probably about 4-5 years old and seems to be telling you it's giving up the ghost. Try using a cooling fan, and check the cost of spares.. or like bro Des said, time for a new amp ;) Oh yes, please don't ever do that out of convenience. You will short the HDMI board. I didnt hot plug and unplug cables....
FookLai Posted May 18, 2020 Posted May 18, 2020 Change a HDMI cable or better still, upgrade to a new AVR. :) A new AVR, I wish, but we are in the midst of a crisis so spending has to be prudent.
FookLai Posted May 18, 2020 Posted May 18, 2020 This is due to a HDMI cable in your setup is having the common "handshaking problem". Just one intermittent HDMI cable will screw up everything. Just isolate the one cable that is giving this problem if it is still in the system and replace this. My personal cure from this was to change everything to optical HDMI. (Audio) Problem is when I plug my HDMI cable from player to projector, it is working fine. Perhaps you are right, let me try to isolate HDMI cable. Would it help if I turn off the EDID "enchance" in the projector?
Recommended Posts