Guest Moon 600i V2 Posted April 27, 2024 Posted April 27, 2024 15 hours ago, Xecuter said: No it's an sft-1. The sfcd-1 plays hdcd. I do plan to get an sft-3 one day as a nostalgia piece. Mind your fingers.
Sounding Posted June 12, 2024 Posted June 12, 2024 (edited) I've got a couple of racks to show. Both of them I built myself. Before I do, a quick look at what I was using less than 2 years ago. This was just after I upgraded from B&W CM9 to 702 S2 Signature speakers. Moving forward about a year. This rack, when I had Auralic, PrimaLuna and Musical Fidelity as well as some HT equipment. Solid Tasmanian timber, built tall to minimise floor space. This rack is now a bookshelf in another room. The Auralic, PrimaLuna and the Musical Fidelity monoblocks (not in photo) are all sold. I went to the Aus Hifi Show in Sydney and one of the things that caught my eye was the rack that Richter were using. I thought it looked good and decided to get busy on the tools again to house my new hardware. I colour matched the timber as best I could to the speakers, though I admit my spray booth is sub-par. Installation was interesting. And the end result: Quite the upgrade. Stairs and bannister also colour matched. Hoping this inspires people to get creative, a lot can be achieved. A quick listen: You might notice a string around the Contros in the video, a very effective cat deterrent. [EDIT] Don't know where that last unrelated pic came from, now gone. Here's another video. Edited June 15, 2024 by Sounding Irrelevant photo replaced. 15
Barry_72 Posted June 12, 2024 Author Posted June 12, 2024 Looks amazing thanks for sharing the story of the rack build @Sounding 3
Allan Posted June 12, 2024 Posted June 12, 2024 @Sounding I think your cat has claimed ownership of the speakers! Great job on the rack... looks way better 1
muon* Posted June 13, 2024 Posted June 13, 2024 (edited) On 27/04/2024 at 11:44 AM, Gabehcuod said: Any suggestions for a sturdier rack with another tier. Ran out of room with this one, and I have two 40kg amps on the floor in another room. You can see it's already bent on the second tier. The only solution i've seen with enough space is from solidsteel but I can't justify spending $1800 on it. What about taking a cue from the popular Flexy Rack design, easy to make and not expensive. Nice Denon TT BTW. But leave out the rubber washers so It's sturdier. Easy shelf adjustment and leveling with the threaded rods. 1" threaded rods plus hardwood shelves, you can use bench-top hardwood, Bamboo or any other hardwood for the shelves. https://www.pinterest.com.au/pin/finally-have-a-flexy-rack-for-my-hifi-it-was-a-lot-of-work-but-the-end-result-was-totally-worth-it--730357264584108080/ I used MDF which bows at these lengths, so I suggest using a hardwood for the shelving, or have a central threaded rods if going longer with the selves. Edited June 13, 2024 by muon* 2
Dr.Funk Posted June 13, 2024 Posted June 13, 2024 Noting comments about construction materials for DIY racks. Last year I made myself a new router table for my workshop. The previous one was made of MDF (not made by me) and over the years had warped in different places. Which is not good for accurate cuts. The drawers, which were also made of MDF were constantly sticking on humid days. When looking for an alternative material, that would not cost the earth, I remembered the smooth finished Formply that is used for concrete construction. And I quote "Formply is a high-quality plywood produced with FSC certified hardwood timber veneers. These are glued with phenol formaldehyde resin and overlaid with a hard durable resin impregnated paper to give concrete a smooth finish. With a durable A-Type Marine bond, Formply can withstand the rigours of construction moisture. Its hard phenolic surface and high-quality outer veneers make it durable and reusable". It will not bend or warp! There are two versions, stocked at Bunnings if one would like to see them in the flesh, black and brown finish. The black one is structural grade (denoted by the F17 in the description) with no writing impregnated into the surface. The brown is non-structural (makes no difference for cabinet builds) but has writing across the board. If you have access to spray painting equipment, this can be remedied. A full sheet (2400 x 1200 x 17mm) of the black can be currently purchased from Bunnings at $95 and smaller handy-man sheets often come up on special for around $45, these will easily do two 600 x 600mm side panels or sometimes 900 x 600mm depending on the special. Being a standard material for the construction industry it would pay to look at dedicated plywood suppliers for better pricing. Last week I was quoted $76 inc for a full sheet. If you buy any other plywood from Bunnings, regardless of thickness, it is going to be imported junk. Look at the reviews attached to Marine Grade Plywood, many, many people complain of them de-laminating and once cut, the edges have gaps and holes. This is caused in the manufacturing process where the veneers that are bonded are not complete sheets. Marine is supposed to be the best grade you can buy. I have included a couple of images so that you can see what I am describing. 4
Steever Posted June 13, 2024 Posted June 13, 2024 5 hours ago, Sounding said: Gorgeous. What are the little black squares under each foot? I have a new rack I'm refurbishing currently and really don't want to spend the high asking price on a set of Gaia I or Titan footers. Was planning on sourcing some high durometer Sorbothane as an alternative. Cheers.
Steever Posted June 13, 2024 Posted June 13, 2024 (edited) 8 minutes ago, Dr.Funk said: There are two versions, stocked at Bunnings if one would like to see them in the flesh, black and brown finish. The black one is structural grade (denoted by the F17 in the description) with no writing impregnated into the surface. The brown is non-structural (makes no difference for cabinet builds) but has writing across the board. If you have access to spray painting equipment, this can be remedied. A full sheet (2400 x 1200 x 17mm) of the black can be currently purchased from Bunnings at $95 and smaller handy-man sheets often come up on special for around $45, these will easily do two 600 x 600mm side panels or sometimes 900 x 600mm depending on the special. Being a standard material for the construction industry it would pay to look at dedicated plywood suppliers for better pricing. Last week I was quoted $76 inc for a full sheet. If you buy any other plywood from Bunnings, regardless of thickness, it is going to be imported junk. Look at the reviews attached to Marine Grade Plywood, many, many people complain of them de-laminating and once cut, the edges have gaps and holes. This is caused in the manufacturing process where the veneers that are bonded are not complete sheets. Marine is supposed to be the best grade you can buy. That black form ply looks exactly like what I'm looking for to replace glass shelves in a new/old rack I've just picked up on marketplace. And re the Bunnings ply, I've been through entire racks at a couple of Bunnings stores now and every single standard grade board had severe warping. I paid extra for the "higher grade" marine ply. It was heavier but when cut, was full of voids. I don't imagine they'll have many repeat ply customers... Edited June 13, 2024 by Steever 1
Dr.Funk Posted June 13, 2024 Posted June 13, 2024 Holes in Marine Ply is not conducive to building boats! 2
Allan Posted June 13, 2024 Posted June 13, 2024 (edited) 57 minutes ago, Dr.Funk said: Noting comments about construction materials for DIY racks. Last year I made myself a new router table for my workshop. The previous one was made of MDF (not made by me) and over the years had warped in different places. Which is not good for accurate cuts. The drawers, which were also made of MDF were constantly sticking on humid days. When looking for an alternative material, that would not cost the earth, I remembered the smooth finished Formply that is used for concrete construction. And I quote "Formply is a high-quality plywood produced with FSC certified hardwood timber veneers. These are glued with phenol formaldehyde resin and overlaid with a hard durable resin impregnated paper to give concrete a smooth finish. With a durable A-Type Marine bond, Formply can withstand the rigours of construction moisture. Its hard phenolic surface and high-quality outer veneers make it durable and reusable". It will not bend or warp! There are two versions, stocked at Bunnings if one would like to see them in the flesh, black and brown finish. The black one is structural grade (denoted by the F17 in the description) with no writing impregnated into the surface. The brown is non-structural (makes no difference for cabinet builds) but has writing across the board. If you have access to spray painting equipment, this can be remedied. A full sheet (2400 x 1200 x 17mm) of the black can be currently purchased from Bunnings at $95 and smaller handy-man sheets often come up on special for around $45, these will easily do two 600 x 600mm side panels or sometimes 900 x 600mm depending on the special. Being a standard material for the construction industry it would pay to look at dedicated plywood suppliers for better pricing. Last week I was quoted $76 inc for a full sheet. If you buy any other plywood from Bunnings, regardless of thickness, it is going to be imported junk. Look at the reviews attached to Marine Grade Plywood, many, many people complain of them de-laminating and once cut, the edges have gaps and holes. This is caused in the manufacturing process where the veneers that are bonded are not complete sheets. Marine is supposed to be the best grade you can buy. I have included a couple of images so that you can see what I am describing. some excellent info... cheers! Bunnings, huh. Was there a few weeks back buying some 90 x 45 H3 for door frames. The Bunnings tradie said, take your time looking through the pile mate, most of its warped. He wasn't wrong!!! I'll soon be after some high grade marine or birch ply, where's the best place in Vic to buy it? Edited June 13, 2024 by Allan
Dr.Funk Posted June 13, 2024 Posted June 13, 2024 @Allan I buy my timber and Ply from these guys here in Perth, they have outlets all over Oz; let me know if there is one near you? https://www.bigrivergroup.com.au/contact-us/ 1
Allan Posted June 13, 2024 Posted June 13, 2024 2 minutes ago, Dr.Funk said: @Allan I buy my timber and Ply from these guys here in Perth, they have outlets all over Oz; let me know if there is one near you? https://www.bigrivergroup.com.au/contact-us/ yep the Epping outlet would be my closest. thanks!
Dr.Funk Posted June 13, 2024 Posted June 13, 2024 @Allan I should imagine their standard is the same across the board (pun intended). I have bought CCA and it is straight as an arrow, even their CCA sleepers for retaining walls are great quality. Over here, if you know what you are talking about and have a tape attached to your belt, cash sales get a 30% discount, no need for an account. Let me know how they shape up for you. Cheers Andy
Flash Posted June 13, 2024 Posted June 13, 2024 Buying timber from Bunnings is a lottery at any time. I’ve just recently built a CD rack with, admittedly just radiata, from there. What was planned to be a super low budget project, cost me more than it should, due to having to buy more material because of warps, woofs, and cracks. The way they rack it is abysmal, and if you mention anything, their eyes glaze over.
Allan Posted June 13, 2024 Posted June 13, 2024 5 hours ago, Dr.Funk said: @Allan Over here, if you know what you are talking about and have a tape attached to your belt, cash sales get a 30% discount, no need for an account. Let me know how they shape up for you. Cheers Andy Thanks Andy, will do
Sounding Posted June 15, 2024 Posted June 15, 2024 (edited) On 13/6/2024 at 2:59 PM, Steever said: What are the little black squares under each foot? They are just some squares of Bunnings vibration mat that I chopped up, mainly to make a larger surface area for each foot on the floor. https://www.bunnings.com.au/jack-200-x-200-x-15mm-anti-vibration-square-2-pack_p3961976 The equipment rack weighs close to 200kg so I figured a larger footprint surface area is a bit kinder on the floorboards. You will also notice a few stacked in the centre between the amps, to help hold the shelf - same at the back. That's to stop the shelf bending with the weight of the amps - 100kg or so. EDIT - found this photo to add, you'll see it also has a rubber mat cut out and stuck to it. Edited June 19, 2024 by Sounding Added photo. 3
Peter_F Posted June 15, 2024 Posted June 15, 2024 (edited) I recently finished a DIY wooden rack made from 100% recycled materials. The shelves are 25mm and 38mm (2 x 19mm) jarrah veneered particle board salvaged from an office demolition in East Perth a couple of years ago. The jarrah used for the legs and shelf edging was salvaged from my late father-in-law's massive 40 year old firewood stockpile. The finish is a water based brush applied sealer used as top coat over old recycled oil based varnishes used as a grain sealer. Hoping to get it place soon when time allows. Edited June 15, 2024 by Peter_F 15 6 1
RankStranger Posted June 17, 2024 Posted June 17, 2024 On 13/6/2024 at 3:51 PM, Allan said: I'll soon be after some high grade marine or birch ply, where's the best place in Vic to buy it? I’ve gotten plywood for a few projects over the years from Plyco in Fairfield. Always been happy with the quality and service
Chill3 Posted June 30, 2024 Posted June 30, 2024 19 minutes ago, Chill3 said: For a Yamaha GT2000, two ikea https://www.ikea.com/au/en/p/laemplig-chopping-board-bamboo-20309828/ make a perfect platform 1
Chill3 Posted June 30, 2024 Posted June 30, 2024 1 hour ago, Chill3 said: For a Yamaha GT2000, two ikea https://www.ikea.com/au/en/p/laemplig-chopping-board-bamboo-20309828/ make a perfect platform Yep times 2 with damping silicone between in my case perfect fit for GT2000, would still work for smaller TTs icoj
Guest Posted June 30, 2024 Posted June 30, 2024 This was my design, utilising (extensively) IsoAcoustics. I had my dad weld it up, then had it powdercoated locally. Tops are granite offcuts from the local stonemason. It's been flawless and will likely stand longer than the home itself will! It cost a fair penny when all was said and done. Using 6 x Orea Bordeaux per shelf, and 4 x Gaia feet. 11 2
Be Quiet...Listen Posted June 30, 2024 Posted June 30, 2024 3 hours ago, Marc said: This was my design, utilising (extensively) IsoAcoustics. I had my dad weld it up, then had it powdercoated locally. Tops are granite offcuts from the local stonemason. It's been flawless and will likely stand longer than the home itself will! It cost a fair penny when all was said and done. Using 6 x Orea Bordeaux per shelf, and 4 x Gaia feet. How do you find the granite Marc? In my trials thus far it hasn't been positive. And that seems to be the consensus of the knowledgeable heads I know well.
Be Quiet...Listen Posted June 30, 2024 Posted June 30, 2024 Hardwood timber rack. Finished in a dark walnut stained satin polyurethane. It's doing a good. Thats approx. 130kg's of analogue gear up top. 7 2
Steever Posted July 1, 2024 Posted July 1, 2024 For space reasons, I recently consolidated from my Cyrus Hark stand and separate turntable stand to a single steel and glass stand from Gecko. The electronics perform just as well on the new stand but, the turntable really shone on the dedicated stand. I guess I’ll need to look at platforms or a different shelf material for the table now… 3
.thumb.jpeg.a4b7d7f34dec3344afad6af9c8fd6c9d.jpeg)
Recommended Posts